After many years of riding many kinds of bikes, I finally bought a Himalayan and that was delivered on the 14th.
From my experience I wanted to write about a few basic things a new Himalayan owner should know- some stuff i could not find on the net when I picked up my bike.
1. Tire Pressure
Roads, and hard ground
SOLO- 25F 32R
PILLION- 27F 34 R
Sand and very soft mud- this is very subjective and best learnt with a lot of riding experience.
20-22F and 26-28R
Remember that bikers you see on trails in africa or the US or Europe, are often ridng with slightly low air pressure but with 4mm thick butyl tubes, which enhance the integrity of the tires and make sure that the side walls act as cushions to prevent rim damage.
2. Running in- very important
The idea behind running in is to allow the piston and the cylinder liner to get mated and the pitons rings to get pushed back and out and allow them to be 'bedded' properly.
RE recommends a top speed of 60Kmph, which runs the engine at about 3000RPM. Using this as a benchmark, the idea will be as follows-
Start the engine before you wear your helmet and gloves so that it has time to start circulating the oil that would be cold and pooled at the bottom of the crankcase.
Change gears between 2200-3000rpm and keep the bike moving.... while lowering gears every time you have a drop in momentum, or you feel the gradient has changed.
When in 5th gear, you can maintain 3000rpm, but keep varying the throttle position, and load on the engine, say by cutting the throttle to zero while coming down a bridge
Keep varying the gears and speeds while avoiding static throttle- so what would be an ideal run? If you know Mumbai city- a weekday ride from Thane to VT- would give you decent straights and a dozen flyovers and a lot of miserable bumper-to-bumper traffic so that in a distance of 60-odd Km you could not hold a steady throttle for too long, and mess up you liner.
Riding from Pune to Lonavala or Mumbai to Dhule is NOT the right way to do this- flat roads and hardly any variation in the throttle position.
This messing up happens when some larger metal particle gets caught in the cylinder space and cannot get dislodged- and causes a groove in the liner. The recommended change of oils, I have asked for one additional- and you should try this- take a fine muslin cloth and drain that oil at 200Km, and if possible spin a magnet in it for a few mins, and you will be surprised at the kind of fine metallic dust you will see. And if you dont, you can only thank yourself for checking. Total cost will be about 800-900 bucks, which with the 2L Rupee bike, is nothing for 'engine insurance.'
Now the oils- the idea of the running in is to allow the piston and the piston rings to be properly worn in. If you use synthetic oil or some really nice oil, you would be interfereing with this, and therefore its a request to stick to company oil, till atleast the 2000km run-in is complete.
Riders using Google will find alternate methods of running-in like riding full tilt, and absolutely hammering the engine- like it happens in the case of race bikes. Please remember we are not having race bikes nor does RE have metallurgists who are designing these kinds of bikes.
3. Oil Change + filter change at all three times
@200Km just to wash out any crap that may be there in the engine- this is the burrs that come off the gears and all other parts that mesh and which accumulate at the bottom due to gravity overnight.
@500Km at first service
@2000Km at second service
Use factory Liquid Gun till this 2K service. After this till 5000 you can use MOTUL that comes recommended by many across various forums, and then after 10,000 you can use fully synthetic, or whatever you want thereon.
For some reason, the first oil change is 2.3L, whereas subsequent oil changes are 'about 2L' and this is something I will figure out soon or maybe i have read something wrong.
While changing oil, always try and let the oil drain for a good 10-15 minutes after opening all drain holes and removing the air filter too. Just have patience and leave it alone.
I will look at putting in my feedback on the ride experience and as and how the bike gets treated at Service time. I invite owners to send in their comments on what we new guys/gals can watch out for.
#REH #Himalayan #RoyalEnfield #HimalayanSleet
PS- repeat there are others who talk about nikasil-coated cylinders and advanced metallurgy- apparently none of this applies to RE
as they advise the slow run-in in their owners manual. As always other view points are welcome.
From my experience I wanted to write about a few basic things a new Himalayan owner should know- some stuff i could not find on the net when I picked up my bike.
1. Tire Pressure
Roads, and hard ground
SOLO- 25F 32R
PILLION- 27F 34 R
Sand and very soft mud- this is very subjective and best learnt with a lot of riding experience.
20-22F and 26-28R
Remember that bikers you see on trails in africa or the US or Europe, are often ridng with slightly low air pressure but with 4mm thick butyl tubes, which enhance the integrity of the tires and make sure that the side walls act as cushions to prevent rim damage.
2. Running in- very important
The idea behind running in is to allow the piston and the cylinder liner to get mated and the pitons rings to get pushed back and out and allow them to be 'bedded' properly.
RE recommends a top speed of 60Kmph, which runs the engine at about 3000RPM. Using this as a benchmark, the idea will be as follows-
Start the engine before you wear your helmet and gloves so that it has time to start circulating the oil that would be cold and pooled at the bottom of the crankcase.
Change gears between 2200-3000rpm and keep the bike moving.... while lowering gears every time you have a drop in momentum, or you feel the gradient has changed.
When in 5th gear, you can maintain 3000rpm, but keep varying the throttle position, and load on the engine, say by cutting the throttle to zero while coming down a bridge
Keep varying the gears and speeds while avoiding static throttle- so what would be an ideal run? If you know Mumbai city- a weekday ride from Thane to VT- would give you decent straights and a dozen flyovers and a lot of miserable bumper-to-bumper traffic so that in a distance of 60-odd Km you could not hold a steady throttle for too long, and mess up you liner.
Riding from Pune to Lonavala or Mumbai to Dhule is NOT the right way to do this- flat roads and hardly any variation in the throttle position.
This messing up happens when some larger metal particle gets caught in the cylinder space and cannot get dislodged- and causes a groove in the liner. The recommended change of oils, I have asked for one additional- and you should try this- take a fine muslin cloth and drain that oil at 200Km, and if possible spin a magnet in it for a few mins, and you will be surprised at the kind of fine metallic dust you will see. And if you dont, you can only thank yourself for checking. Total cost will be about 800-900 bucks, which with the 2L Rupee bike, is nothing for 'engine insurance.'
Now the oils- the idea of the running in is to allow the piston and the piston rings to be properly worn in. If you use synthetic oil or some really nice oil, you would be interfereing with this, and therefore its a request to stick to company oil, till atleast the 2000km run-in is complete.
Riders using Google will find alternate methods of running-in like riding full tilt, and absolutely hammering the engine- like it happens in the case of race bikes. Please remember we are not having race bikes nor does RE have metallurgists who are designing these kinds of bikes.
3. Oil Change + filter change at all three times
@200Km just to wash out any crap that may be there in the engine- this is the burrs that come off the gears and all other parts that mesh and which accumulate at the bottom due to gravity overnight.
@500Km at first service
@2000Km at second service
Use factory Liquid Gun till this 2K service. After this till 5000 you can use MOTUL that comes recommended by many across various forums, and then after 10,000 you can use fully synthetic, or whatever you want thereon.
For some reason, the first oil change is 2.3L, whereas subsequent oil changes are 'about 2L' and this is something I will figure out soon or maybe i have read something wrong.
While changing oil, always try and let the oil drain for a good 10-15 minutes after opening all drain holes and removing the air filter too. Just have patience and leave it alone.
I will look at putting in my feedback on the ride experience and as and how the bike gets treated at Service time. I invite owners to send in their comments on what we new guys/gals can watch out for.
#REH #Himalayan #RoyalEnfield #HimalayanSleet
PS- repeat there are others who talk about nikasil-coated cylinders and advanced metallurgy- apparently none of this applies to RE
as they advise the slow run-in in their owners manual. As always other view points are welcome.